Instructions X-cruise II

X-cruise II

Congratulations on your new one X-cruise II for motorcycle.
Learn to operate X-cruise II before you use it when driving, for your own safety and that of other road users.
X-cruise II may only be used on motorcycles where the arm cannot reach under the brake lever. Certain types of brake levers can be pushed forward, check that the arm cannot get under the brake lever when it is pushed forward.

X-cruise II is designed to be able to hold the throttle only in a continuously selected position. It must not be tight in any way when you have to take off the gas again.
If it can be tightened with the screw (E) so that it is tight or difficult to disable, please remove it and contact us for a solution.

X-cruise II only need to hold the throttle and be able to easily turn the throttle back to the idle position.
Before you drive after you have fitted your X-cruise II, and learn to operate it with the engine off.
X-cruise II is by no means accurate in its retention of speed. When driving up and down hilly terrain, the speed of the motorcycle will decrease and increase, respectively.

You can adjust how tight the brake is X-cruise II must be by means of the screw (E). Be sure to adjust the cruise control before driving.

Cruise control
Dimensions (W x H x D): 110 x 52 x 11mm
Veight: 29gr.
Material: Plastic

Bolts, nuts and screws
A2 stainless

Mounting of X-cruise

Measure the diameter of your throttle body with a ruler. Your throttle must be between 29 – 35 mm ro 38 – 43 mm depending on model in order to use X-cruise II. Contact us for special measurements.
In order for the anti-blocking to be effective, it is extremely important that you use the adapter ring that has the same inner diameter as your throttle.

Find the adapter ring that has the same dimensions as your throttle. 7 different sizes from 29 to 35 mm or 6 sizes from 38 to 43 mm are supplied, depending on model, with 1 mm interval.
It is extremely important that you use the correct size ring, otherwise the X-cruise will not function as intended and, in the worst case, result in an accident.

1. Adapter ring (C) is placed as far to the left of the throttle as it will go. You can gently extend the inner ring with 2 fingers to just tip the adapter ring over the edge of the throttle or handlebar weight. It’s a little tight, but it has to be.
2. If necessary, remove steering weights if the diameter is larger than the throttle. The inner ring is conical inside, so it must be placed with the thin side to the left.
3. Fit the X-cruise control (A) over the adapter ring (C).

X-cruise in use

Activating
achieved the speed you want to maintain, you press down on the arm with your index finger X-cruise II downwards.
You can give additional gas if necessary. notice that the X-cruisee II stops at the point where it was activated if you gentle release the grip on your throttle, allowing your speed to drop back to the point you had set before accelerating.

Deactivating
When you need to deactivate the cruise control, simply turn the throttle back to the idle position. Just as you would normally do when accelerating or braking. It doesn’t take any longer than if you didn’t have it installed, or require other measures for deactivation.
If the throttle is too tight and makes deactivation difficult, do not activate it in any way. Should it happen while driving that X-cruisee II feels tight to deactivate, you can activate clutch and possibly dead man’s button and drive to the side as quickly as possible to remove (A) X-cruise II.

Sand, gravel and mud
Disassemble X-cruise II if you have to drive off-road, on the beach, in the forest or in other places where there is an increased risk of foreign objects coming into contact with X-cruise II.
Always assess whether the condition of the road is suitable for use X-cruise II.

IMPORTANT!
Make sure all parts are free of dirt and foreign objects before assembly.
Dirt and e.g. sand between adapter ring and the X-cruise II can increase friction and prevent unimpeded turning of the throttle.
Never use strong solvents for cleaning X-cruise II and the adapter ring.
Extreme heat can cause the parts to deform and prevent the throttle from turning freely.

Never use X-cruise II if the throttle cannot easily return to the idle position by itself when screw (E) is loosened.
If you know in advance that you will not need X-cruise II, we recommend that it be dismantled.

Usage
Use only the X-cruise where there is limited traffic and good visibility.
Do not use X-cruise in urban areas and always make sure to pay special attention to traffic in front and always keep a good distance.
Always drive with both hands on the handlebars.
Do not use the X-cruise during gear changes.

Disclaimer
It is your own responsibility to operate X-cruise in a responsible and safe manner, and not to violate the law.

X-cruise may not be used for negligence.
X-MC Parts ApS disclaims all liability for loss, damage or inconvenience, both direct and indirect of any kind.

Warranty
2 years according to the provisions of the Purchase Act.

X-MC Parts ApS
Eliassensvej 43, DK-6000 Kolding, Denmark
Phone +45 93 94 36 96
Email: support@x-mcparts.com

Danish design and production